Short answer
A fire-rated gypsum partition is a drywall wall system (steel studs, fire-resistant gypsum boards and usually mineral wool in the cavity) that has been tested to stop fire passing through it for a set time, commonly 30, 60, 90 or 120 minutes. The rating belongs to the complete tested system. It holds only if the wall on site matches the test: the same boards, the same number of layers, the same studs and insulation, and the same sealing at joints, head and every opening.
That last condition is where most rated walls go wrong. We built fire-rated gypsum partitions and cement board walls at Giza Palace Hotel & Spa between 2022 and 2025, and the checks below are the ones we apply to every rated wall. This guide covers what the ratings mean, how typical 60 and 120-minute walls are built, and the site mistakes that cancel a rating.
What does a fire rating in minutes mean?
A rating in minutes is the time a sample of the wall survived a standard furnace test while meeting set criteria. For a non-loadbearing partition the two that matter are:
- Integrity: no flames or hot gases pass through cracks or gaps
- Insulation: the unexposed face stays below a set temperature rise, so materials on the safe side don't ignite
European test reports express this as, for example, EI 60: integrity and insulation for 60 minutes [1]. British BS 476 [2] and American ASTM E119 [3] tests use different methods but the same idea. Specifications in Egypt often reference one of these standards, so check which one your consultant has named and ask for test evidence to that standard.
Is fire-resistant (red or pink) board the same as a fire-rated wall?
Fire-resistant board and a fire-rated wall are different things. Fire-resistant gypsum board has a core reinforced with glass fibres and additives so it holds together longer in a fire. Many manufacturers colour it pink or red, but the colour is a convention, not a standard, and it varies by brand. A single fire-resistant board on its own has no wall rating. The rating comes from the assembly it was tested in.
The same caution applies to moisture-resistant board, often green. A wet-area wall in a hotel may need both properties, and some boards combine them. Go by the data sheet and the tested system, not the colour on the delivery truck.
How are 60 and 120-minute partitions typically built?
Build-ups differ by manufacturer, so treat the table below as orientation only [4]. The approved system data sheet is the only build-up that counts on site.
| Rating | Typical build-up in many manufacturers' systems | Points to check |
|---|---|---|
| 30 minutes | One layer of board each side of steel studs; some systems allow standard board | Often used inside apartments, rarely enough for hotel corridors |
| 60 minutes | One layer of 12.5 or 15 mm fire-resistant board each side, steel studs, mineral wool in the cavity | Common for room-to-corridor walls; check stud size and spacing |
| 90 minutes | Two layers each side, or thicker specialist boards | Less common; confirm the exact system |
| 120 minutes | Two layers of fire-resistant board each side, staggered joints, mineral wool | Risers, shafts, escape stairs; heavier, needs more care at the head |
Where do hotels and residential towers need fire-rated partitions?
The building's fire strategy decides, prepared by the fire consultant and approved under the Egyptian fire code and civil defence requirements. In hotels and multi-storey residential buildings, rated walls usually include:
- Walls between guest rooms (or apartments) and the corridor
- Walls between neighbouring guest rooms or apartments
- Enclosures around stairs, lifts and escape routes
- Service risers and shafts
- Plant rooms, kitchens and storage
How do fire-rated walls fail on site?
A wall can be built from the right boards and still fail its rating. These are the mistakes that come up again and again:
- The wall stops at the suspended ceiling. A rated partition normally runs from the floor slab to the structural slab above. A wall that stops at ceiling level leaves fire a path over the top.
- A layer is missing or substituted. Two layers become one to save time, or a fire-resistant board is swapped for standard board because the right one ran out.
- Penetrations are left open. Every pipe, duct, cable tray and conduit through a rated wall needs a firestop product tested for that wall and that service.
- The head is fixed rigidly. When the slab above deflects, a rigidly fixed wall cracks. Rated systems use a deflection head detail that stays sealed as the slab moves.
- Joints are not staggered. In two-layer walls, the outer layer's joints must be offset from the inner layer's, as tested.
- Doors, access panels and glazing are unrated. An opening in a 60-minute wall needs a 60-minute door or panel.
FUTURE plans every penetration on the shop drawings and builds to the system named in the specification, layer by layer. Fire-rated partitions were part of our package at Giza Palace Hotel & Spa, alongside the hotel's ceilings.
Where does cement board fit in?
Cement board is a dense, reinforced board made with cement. It does not soften in water, so it is used for wet-area walls behind tiles, walls exposed to impact or washing, and claddings. Some cement board systems also carry fire ratings, but as with gypsum, only as tested assemblies. At Giza Palace, FUTURE built cement board partitions and claddings in the same package as the fire-rated gypsum walls.
What should the BOQ and specification say?
For quotations you can compare, each rated wall type in the BOQ should state:
- The required rating and the test standard
- The named system or "approved equal" with test evidence
- Board type, thickness and number of layers each side
- Stud size and spacing, and the insulation
- Height (slab to slab) and head detail
- Who supplies and installs firestopping at penetrations
Frequently asked questions
In most cases yes. A rated partition usually continues through the ceiling void to the structural slab above, so fire cannot pass over the top. The exception is a tested system where a rated ceiling forms part of the separation.
Only if the tested system you are following specifies it. Most 60 and 120-minute systems use fire-resistant board.
The board is fire-resistant. The wall, built as a tested system, is fire-rated for a stated time.
A 60-minute wall cannot take a normal door. Doors, access panels and glazed screens in a rated wall need a matching rating, or the wall's rating no longer holds.
Sources
- EN 1363-1 and EN 1364-1: fire resistance tests, general requirements and non-loadbearing walls (CEN)
- BS 476-22: fire tests on building materials and structures, non-loadbearing elements (BSI)
- ASTM E119: standard test methods for fire tests of building construction and materials (ASTM International)
- Published partition system data from gypsum manufacturers (for example Knauf and British Gypsum) for 60 and 120-minute stud walls, consulted November 2026