Aluminum and metal strip ceilings

Aluminum and metal strip ceilings for humid and coastal spaces

Where steam, salt air or open sides would stain or sag a gypsum ceiling, a metal strip ceiling stays straight. FUTURE has supplied and installed them on three Red Sea resorts.

Last updated

S-03 Aluminium linear strip ceiling. Typical section across an aluminium strip ceiling: rod hangers with adjustment springs, a toothed carrier at a 100 mm module, 84 mm round-edged strips with 16 mm open joints, an optional filler strip and a wall trim.SSLFCL300 max1700 max8416100 modulePLENUM VARIES1234567
  1. Anchor fixed to the slab
  2. Rod hanger with adjustment spring, 1700 max c/c along the carrier
  3. Carrier: slim channel with clip-in teeth at 100 mm module, 1500 max c/c; 300 max cantilever past the last hanger
  4. Aluminium strip 84 mm, round edge (84R type), clipped on
  5. Open joint 16 mm
  6. Filler strip for a closed joint (optional)
  7. Wall trim (edge profile) fixed to wall
Typical sectionMetal strip ceiling
ScaleNTS
SheetS-03
Ref: EN 13964 · manufacturer system dataTypical detail. Indicative only. Project details per approved shop drawings.

01

What is a metal strip ceiling?

FUTURE supplies and installs aluminum and metal strip ceilings, also called linear ceilings: long, narrow aluminum or steel strips clipped onto carriers that hang from the slab. The strips are factory-finished, usually powder-coated, so there is no jointing or painting on site. Metal does not absorb moisture, and aluminum does not rust, which is why strip ceilings suit wet and coastal areas.

02

Where does a metal strip ceiling make sense?

  • Guest bathrooms and shower areas
  • Spa wet areas and pool surrounds
  • Terraces, walkways and semi-open spaces on coastal resorts
  • Restaurants and public areas where the designer wants a linear look
  • Service areas that need a washable, demountable ceiling

On our projects, strip ceilings went into Jaz Costa Mares in Marsa Alam, Jaz Elite Asteria in Sahl Hasheesh and Casa Del Mar in Hurghada.

03

Strip ceiling options

ChoiceOptionsNote
MaterialAluminum, galvanised steelAluminum for coastal and outdoor areas
JointOpen joint (gaps between strips), closed jointOpen joints let air through and suit ventilated spaces
Strip widthNarrow and wide profiles, single or mixedMixed widths give a less regular rhythm
FinishPowder-coated colours, wood-effectSpecify a coating rated for coastal exposure on Red Sea sites

04

How does FUTURE avoid the usual strip ceiling failures?

FUTURE avoids strip ceiling failures by solving them on the shop drawings before any carrier is fixed. Strip ceilings usually fail at the edges and at the carriers. When strips are not set out from the centre of the room, they end in thin slivers at the walls, which look like a mistake and are hard to put right. When carriers are spaced too far apart, long strips sag between them. On coastal sites, unprotected fixings rust first and stain the strips. FUTURE draws the strip layout for every room, centring it so the edge strips match on both sides, and follows the carrier spacing the strip manufacturer specifies. For Red Sea and North Coast projects, FUTURE recommends aluminum strips with a coating rated for coastal exposure and corrosion-protected fixings, and raises any gap in the specification at tender stage.

05

Where has FUTURE installed metal strip ceilings?

FUTURE has installed aluminum and metal strip ceilings on three Red Sea projects. At Jaz Costa Mares Resort in Marsa Alam (2021 to 2022), the farthest south of FUTURE's projects, the package covered the guest rooms in buildings H1 and H3 and included metal strip ceilings. At Jaz Elite Asteria Resort in Sahl Hasheesh (2023 to 2025), aluminum strip ceilings sat alongside gypsum board ceilings and gypsum tiles across the rooms, suites, main building and the Arabian and Asian restaurants. At Casa Del Mar Beach Hotel in Hurghada (2019 to 2021), metal strips were one of three systems, with gypsum board and gypsum tiles, in a hotel that combined rooms, corridors, a reception, a French café, an Italian restaurant, a gym, meeting rooms, offices and a food court. All three sites are on the coast, where humid, salty air is a daily condition for every ceiling in the building.

06FAQ

Metal strip ceiling questions

In wet and semi-open areas, usually yes: aluminum does not absorb moisture or rust. In air-conditioned rooms, moisture-resistant gypsum board performs well and gives a jointless finish. Most coastal hotels use both, matched room by room.

Strip ceilings come down for maintenance without damage. The strips unclip from their carriers, so services above can be reached and the strips refitted.

Building on the coast?

Send us the BOQ and the wet-area drawings. We will tell you where strips will outlast board, and price both.